,

24 V solar surface pump – 210 W, 2 m³/h, 25 m head

€349.00 incl. VAT

High-pressure solar surface pump for watering, filling elevated tanks and supplying water away from the grid. Maximum flow 2 m³/h, maximum head 25 m, 210 W brushless motor (24 V DC) and 30–48 V MPPT controller built into the pump. Inlet and outlet: 1 inch.Recommended supply: a single panel of about 400 Wp (300 Wp minimum).Solar panel sold separately. Actual flow depends on head and sunlight.

Available on back-order

Secure payment by card, PayPal, Apple Pay or Google Pay.

Well-documented choice
Clearly detailed specifications

Tailored response
Configuration matched to your site

Tracked delivery
Arranged to suit the project

Flocea support
A named point of contact

SKU: FLO-SQB2-25-24-210
Category: ,

Description

What is included in your purchase

The pump with its built-in MPPT controller and accessories. Solar panel, pipes and DC protection are sold separately.

A vegetable garden to drip-irrigate, a rainwater tank to make use of? The Flocea 24 V – 210 W solar surface pump is the most compact Flocea solar pump: a single panel is enough. Its MPPT controller is built into the pump housing: the panel connects directly to it, with no separate box, no battery and no electricity bill.

2 m³/hmaximum flow
25 mmaximum head
210 W24 V brushless motor
1″ / 1″inlet / outlet
Low flow, high head. 2 m³/h and 25 m are two separate maximums: at 10 m head the pump delivers about 1.3 m³/h, i.e. 1,350 L/h, in full sun. Useful flow depends on elevation, pipework, required pressure and sunlight.

What is it for?

Vegetable garden watering

Run a drip line or micro-sprinklers with the sun, with no power socket in the garden.

Rainwater tank

Pump water from a rainwater tank or cistern to water wherever you need it.

Small water points

Fill a trough, a tub or a small reservoir, even some twenty metres higher.

The pump stands out of the water, in a dry place, as close to the source as possible and as little as possible above the water level. The 25 m head is not a suction depth: for a well or borehole you need a submersible pump. It is designed for clear water: a strainer is essential.

Flocea 210 W solar surface pump connected to a rainwater tank, feeding a drip line in a vegetable garden, with one solar panel
Installation illustration: pump with built-in controller; a single panel, mount and pipes sold separately.

Specifications of the Flocea 24 V – 210 W pump

Brand Flocea
Type High-pressure solar surface pump, clear water
Motor Brushless DC, 210 W; rated voltage 24 V
Maximum flow 2 m³/h = 2,000 L/h = 33.3 L/min, at very low head
Maximum head 25 m, at zero flow
Inlet / outlet 1″ / 1″ (DN25); check the thread type for fittings
Controller MPPT built into the pump housing, with display
MPPT voltage range 30–48 V DC
PV array open-circuit voltage Strictly below 50 V, cold correction included
Minimum PV power 300 Wp
Indicative set-up 1 panel of 400 Wp
Cable 2 m
Reference FLO-SQB2-25-24-210
Specifications of the Flocea 24 V 210 W solar pump: 2 m³/h, 25 m head, 1-inch connections

Work out the total head of your installation

Before comparing flow rates, estimate the total head the pump will have to deliver. Two measurements are enough.

Diagram: working out the total head of a solar surface pump. H is the height difference between the water level and the outlet into the tank, L the pipe length; total head ≈ H + 10% × L, plus 10 m per bar of pressure needed at the outlet.
Measure the height difference H and the pipe length L, then apply the formula.

Total head ≈ H + 10% × L

  • H: height difference between the (lowest) water level and the outlet.
  • L: pipe length to the outlet; the 10% covers friction losses.
  • Pressure needed at the outlet (sprinkler, drip line): add 10 m per bar.

Example: tank 8 m above the water level, 50 m of pipe → total head ≈ 8 + 5 = 13 m. With 1 bar needed at the outlet: 13 + 10 = 23 m.

Then go by the flow the pump delivers at that total head, not its maximum flow. Full 3-step method and how to read the curve.

Water more than 7–8 m below the pump? See our solar submersible pumps.

What flow at your head?

Flow decreases as the total dynamic head (TDH) increases. It adds up the suction lift, the elevation to the delivery point, the friction losses in the pipes and the pressure required at the outlet. Useful rule: 1 bar of required pressure ≈ 10 m of extra head.

Example: at 10 m head, expect about 1.3 m³/h (1,350 L/h) in full sun; at 20 m, about 0.5 m³/h. The table and curve give the other duty points.

Head Indicative flow in full sun
5 m ≈ 1.7 m³/h (1,690 L/h)
10 m ≈ 1.3 m³/h (1,350 L/h)
15 m ≈ 1 m³/h (950 L/h)
20 m ≈ 0.5 m³/h (520 L/h)
Flow–head curve of the Flocea 24 V 210 W solar surface pump
Indicative flow according to head, in full sun with the recommended PV power. Flow decreases when sunlight drops.

A single panel: the recommended set-up

The built-in controller works between 30 and 48 V and accepts no more than 50 V open circuit. A single panel of about 400 Wp is enough (300 Wp minimum). Check these values on its label:

Power (Pmax) 300 to 450 Wp
Maximum power voltage (Vmp) 30 to 40 V
Open-circuit voltage (Voc) 45 V maximum (a common 400 Wp panel shows about 37 V)
Number of panels One only, never two in series
Do not connect two panels in series to this 24 V pump: their open-circuit voltage would exceed 50 V and damage the controller.

Simplified wiring

Panel → pump

The solar cable goes straight into the pump housing (P+ / P−), through a DC isolator: no separate box to mount.

Built-in display

The controller display shows the operating status and gives access to the settings described in the manual.

Level probes (option)

Compatible probes can stop the pump when the source runs dry or the reservoir is full.

Wiring diagram of a single panel to the built-in MPPT controller of the 24 V solar pump

Principle diagram, to be completed with the manual of the equipment supplied. Wire with the power off, by a qualified person, then check polarity and voltage before commissioning.

The full Flocea range of solar surface pumps

High-pressure models for low flows and high heads, centrifugal models for large flows: choose according to your needs.

Pump Max. flow Max. head Connections Panels
210 W solar pump – 2 m³/h (this page) 2 m³/h 25 m 1″ 1 × ~400 Wp
280 W solar pump – 2 m³/h 2 m³/h 30 m 1″ 1 × ~400 Wp
550 W solar pump – 3 m³/h 3 m³/h 50 m 1″ 2 × ~450 Wp
750 W solar pump – 3 m³/h 3 m³/h 65 m 1″ 3 × ~450 Wp
550 W solar pump – 6 m³/h 6 m³/h 30 m 1″ 2 × ~400 Wp
550 W solar pump – 18 m³/h 18 m³/h 14 m 2″ 2 × ~400 Wp
750 W solar pump – 21 m³/h 21 m³/h 14 m 2″ 3 × ~450 Wp
1,100 W solar pump – 26 m³/h 26 m³/h 15 m 2″ 3 × ~500 Wp
1,500 W solar pump – 27 m³/h 27 m³/h 21 m 2″ 4 × ~500 Wp
1,500 W solar pump – 55 m³/h 55 m³/h 17 m 3″ 4 × ~500 Wp

Preparing an installation that keeps the flow

  1. Place the pump on a stable, dry base, sheltered from direct rain and frost, as close to the source as possible.
  2. Plan a short, airtight and non-collapsible suction line of at least 1″, with a strainer and foot valve.
  3. Keep the strainer submerged and away from the bottom to limit debris intake.
  4. Fill the pump casing and suction line with water before each start from empty; never run the pump dry.
  5. Size the delivery line according to length: a 32 mm PE pipe for a few tens of metres, 40 mm beyond 100 m.
  6. Connect the panel to the pump housing through a DC isolator, then check fittings and strainer regularly.

Your questions about this solar pump

Does the pump deliver 2 m³/h all the time?

No. 2 m³/h is a maximum flow, at very low head and in full sun. At 10 m head, expect about 1.3 m³/h (1,350 L/h).

Do I need a separate controller?

No. The MPPT controller is built into the pump housing, with its display: just connect the panels to it.

Which solar panel should I choose?

One panel of 300 to 450 Wp: Vmp 30 to 40 V, Voc 45 V maximum. Never two in series.

Can it lift water from a deep well?

No. It is a surface pump: it only draws water up a few metres. The 25 m head is not a suction depth; for a well or borehole, choose a submersible pump.

What pressure at the tap or sprinkler?

Count 1 bar per 10 m of available head. For example, with 10 m of elevation and losses, about 0.4 bar remains usable at a flow of 1 m³/h: have your case checked.

Does it work at night or in cloudy weather?

In direct solar mode it runs only when there is enough PV energy. At night, use the water stored in a reservoir.

What pipe diameter do I need?

The ports are 1 inch. For the delivery line, plan a 32 mm PE pipe for a few tens of metres, 40 mm beyond 100 m.

Let’s start from your water needs

Tell us the daily volume you need, the water level at the source, the elevation, the pipe length, the pressure you want and the model of your panels: we check the right pump before you order.

Solar pump configurator